Tag Heuer Link Bracelet Adjustment

My wife got me a Tag Heuer Link watch for our wedding anniversary.

Of course the metal bracelet/band needed adjustment for my chicken wrist.  I thought of taking it to a jeweler but decided I could probably save myself the time and do it myself.  I like being independent and not counting on others for jobs/tasks I can do myself.  Additionally it gave me the opportunity to examine how the bracelet was put together.

I’ve previously adjusted watch bracelets on my Seiko and Movado ESQ watches.  I’ve also replaced the batteries in many different watches so I’m not a novice to working with them.   There are plenty of watch tools, parts and batteries available online for those willing to dabble.

My first course of action in such a situation is to check the ‘Net to see if someone else had already documented the process.  This is a good website documenting resizing of common watch bracelets.

However I couldn’t find any useful information specific to the Tag Heuer Link bracelet, although I found plenty asking how to do it.  Maybe people who own Tag Heuer watches aren’t the kind who adjust their own watch bracelets.

I did find a message thread where the person claimed the jeweler he had taken the watch to to have the band adjusted didn’t know how to do it. This cemented my decision to have a go at adjusting the bracelet myself.  That, and the potential fame of documenting the process here for the world!

The bracelet appears to have lots of pin ends and spots to push on, so I tried doing that (gently of course) until I discovered the pins I needed to remove to adjust the bracelet.

It’s a really elegant and ingenious design for the band.  It’s also quite simple.

Now here’s my disclaimer:  If you aren’t comfortable with working with delicate items or aren’t handy or coordinated then don’t try this!  The bracelet itself is a bit wiggly and thus hard to handle.

If you mess up you can potentially void the warranty on the band and/or watch, so be careful and proceed at your own risk! I accept no responsibility if you wreck your watch or band following my instructions!

You should work on a soft surface whenever possible and use care not to scratch the crystal (face of the watch).

The bracelet is put together in such a way that in order to adjust its length you only need to remove two link pins, one on each side of the clasp.  (They are labeled “Link Pin 1″ and “Link Pin 2″ in the following photo.  Note:  if you click on the photos you can view larger images.)

IMG_4589a1 copy-medium

These pins need to be pressed out with either a Watch Link Pin Removal Tool (the proper way to do it) or a sturdy small diameter round pin of some sort (I used a fine jeweler’s screwdriver tip) and small hammer.  I used the latter, carefully tapping out the pin until I could grab it with a small needle nose pliers and pull it the rest of the way out. If the pin doesn’t want to move, try pushing it out from the opposite side.

IMG_4532a1 copy-medium

The link pin itself has an indentation nearer to one end than the other.  When you replace the pin you want to have this indentation furthest from the end being pushed into the bracelet as this indentation “locks” the pin into the sleeve.

You want to remove an equal number of links from both sides of the clasp to fit.

Once the link pin is out, you will see that each link in the bracelet is comprised of two halves.  A sleeve aligns the two halves at the top on the link attached to the clasp, and one half is screwed to the next link.  The other loose half simply slips onto the protruding screw head and sleeve (it will only assemble one way).

IMG_4562a1 copy-medium
IMG_4539a1 copy-medium
IMG_4553a1 copy-medium

To remove a link, after removing the loose half, you need to remove the screw holding the other half onto the next link.  Once that is done you can slip the second half of the link off.  All the links are assembled the same way.

IMG_4616a1 copy-medium

Also note that the links are assembled on the bracelet alternately with chrome and matte finishes, so make sure the links alternate properly and that both halves of each link are the same finish.

Once you have removed enough links from each side, you need to reassemble the bracelet to the clasp.  The buckle (clasp latch) goes on the six o’clock side of the watch.  Don’t forget to replace the short sleeve in top end of the last link before putting in the link pin!

IMG_4597a1 copy-medium

There is also a short spring bar/pin that fits in one of three holes on one side of the clasp assembly (shown in the middle of the following photo).  This spring pin can be used for fine adjustment of the bracelet length.

IMG_4589a1 copy-medium

Don’t forget to store the spare links/parts in the event you sell or give the watch to someone else.  I saved my watchbox so the extra links went into a little ziplock in the box.